Menu

Samsung Galaxy S22 broken screen repair guide.

How to replace Samsung S22 Plus Broken Screen-guide

If you are unfamiliar with smartphone repairs, it is advised to seek expert assistance or call an authorized service center. Replacing a cracked Samsung S22 Plus screen might be a difficult operation. However, you can use these broad methods as a guide if you’re at ease and have the required equipment. Please be aware that this article assumes you already have a Samsung S22 Plus replacement screen.

A step-by-step tutorial for replacing the cracked screen on your Samsung S22 Plus is provided below:

  1. Assemble the required equipment: A pair of tiny screwdrivers, a hairdryer or heat gun, a plastic opening tool or guitar pick, tweezers, and adhesive tape are required.
  2. Press and hold the power button until the power options show up on the screen to turn off the phone. To power off the gadget, choose that option.
  3. Locate the SIM card tray on the top edge of the phone, and then remove it. Push a paperclip or a SIM card eject tool into the tiny hole next to the tray to remove it. When the tray pops out, remove it.
  4. Warm up the phone’s edges by using a heat gun or a hairdryer set to a low temperature.
  5. The adhesive keeping the display in place is made softer as a result.
  6. Start by putting a plastic opening tool or guitar pick into the space between the back cover and the phone’s frame to remove the back cover. Separating the back cover off the gadget requires carefully working your way around the edges. Be careful not to harm the internal parts or the plastic back cover.
  7. Locate the battery connector and unplug it from the motherboard to disconnect the battery. This step makes sure that the gadget won’t be powered while the screen is being replaced.
  8. The screen connectors are covered by a metal shield, which may be removed after the rear cover has been taken off. The screws keeping the shield in place should be removed and stored. Using a pair of tweezers or a plastic opening tool, carefully detach the screen flex cables from the motherboard. Lift the damaged screen assembly from the device after the cords have been cut.
  9. Install the new screen assembly: Carefully insert the replacement screen assembly into the machine. Make that the motherboard’s corresponding ports on the connectors are lined up correctly. For the screen to be fixed in place, gently press down.
  10. Reattach the cables, then fasten the metal shield: By inserting them into the relevant ports, the screen flex cables are connected to the motherboard. Put the metal shield back over the connectors when the cables are connected, and fasten it with the screws you previously removed.
  11. Reconnect the battery by inserting the connector into the motherboard’s port.
  12. The rear cover is attached by aligning it with the phone’s frame and gently pressing it down until it snaps into place. Make sure the edges are all firmly fastened.
  13. Try out the new display: Turn on the device to make sure the new screen is working properly. Look for any anomalies, such as touch sensitivity problems or dead pixels.
  14. You’ve now successfully repaired the cracked screen on your Samsung S22 Plus if everything is operating normally. Always take your time, use caution, and adhere to any special instructions supplied by the manufacturer of the new screen or repair manual. It is best to get professional help if you run into any problems or are unclear about any step to prevent further harm to your equipment.

SAMSUNG GALAXY S22 PLUS BATTERY REPLACEMENT

The general procedures for changing a Samsung smartphone battery are as follows:

  1. Assemble the required equipment: A small screwdriver set, a plastic pry tool or spudger, and a spare battery that works with your Samsung device are often required.
  2. Before attempting to change the battery, make sure your phone is completely shut off.
  3. A plastic tool or your fingernail can be used to carefully take off the back cover of your Samsung phone if it is removable. You might need to start by removing the screws that are holding the rear cover to some models.
  4. Warm up the phone’s edges by using a heat gun or a hairdryer set to a low temperature. The adhesive keeping the display in place is made softer as a result.
  5. Start by putting a plastic opening tool or guitar pick into the space between the back cover and the phone’s frame to remove the back cover. Separating the back cover off the gadget requires carefully working your way around the edges. Be careful not to harm the internal parts or the plastic back cover.
  6. Locate the battery connector and unplug it from the motherboard to disconnect the battery. This step makes sure that the gadget won’t be powered while the screen is being replaced.
  7. The old battery can be taken out of its housing by lifting it out after the connector has been released. Use a plastic pry tool to delicately peel the battery away from the adhesive if it is fastened in place using glue.
  8. Place the fresh battery in: Place the new battery in the battery compartment after properly aligning it. Make sure the connectors are lined up straight with the motherboard’s appropriate sockets.
  9. Reconnect the battery by carefully reinstalling the connector to the motherboard’s socket. Make sure it is securely attached and tightly fastened.
  10. If you need to replace the back cover, line it correctly and press firmly until it snaps into place. Screws should be inserted and well tightened.
  11. Turn on your phone by pressing and holding the power button. If the replacement was effective, the gadget ought to start up normally.

It’s crucial to remember that these stages are only general recommendations, and specific models may require a slightly different procedure. Please refer to the user manual or, when it becomes available, seek expert assistance to ensure the precise and secure replacement of your Samsung Galaxy S22 Plus battery. We recommend Nels Mobile Repairs.

Bio:

Am Nelson, a mobile repair expert based in Kenya, Thankyou.

Leave a Reply

Your email address will not be published. Required fields are makes.